Dal Alert!

Receive alerts from Dalhousie by text message.

X

2018 Canadian Electrical Code

Designers, installers and operators of electrical equipment and electrical facilities are responsible for code compliance and public safety. The Canadian Electrical Code provides minimum safety requirements designed to prevent undue electrical fire and shock hazards. This seminar offers important insight into correct application of the code to wiring systems, grounding and bonding, protection and control, motor applications, lines, high voltage substations, hazardous locations, fire alarm systems and emergency systems. It explains the use of other standards referenced throughout the electrical code such as the National Building Code, IEEE, NFPA and CSA are covered as applicable.

The seminar will highlight important changes; some examples:

  • Many familiar terminologies have been redefined for more clarity and to better align with other codes and standards
  • The rules of Section 10, Grounding and Bonding have been completely re-organized along with important revisions
  • Rules previously found in Section 4, Conductors have been moved to Section 12, Wiring Methods
  • The number of connections between the grounded service conductor (neutral) and ground have been reduced to one, leading to new wiring methods
  • New types of equipment, materials and technology are introduced along with applicable rules
  • Tamper-resistant receptacles in areas where children may be present
  • Ground fault circuit interrupters for electric heating devices and controls

Participants should bring a copy of the 2018 Canadian Electrical Code to the course as it will be frequently referenced throughout the two days.

You Will Receive

Each participant will receive a set of notes that will serve as reference and information.

Who Should Attend

This seminar will be of interest to engineers, technologists, contractors and management involving design, construction, maintenance, plant management, electrical utility operations, manufacturing and government.

Course Objectives

Electrical code compliance is a mandatory requirement in all provinces and territories of Canada. Up-to-date electrical code knowledge is fundamental to accurate specification, installation and operation of electrical equipment and facilities. Compliance is a legal requirement. This seminar offers participants a comprehensive understanding of the code in a broad range of its application.

Format

Day 1 - registration/check-in will start at 8:00 a.m. with sessions to begin at 8:30 a.m. and adjourn at 4:00 p.m. Day 2 will commence at 8:30 a.m. and adjourn at 4:00 p.m. There will be 15 minute mid-morning and afternoon breaks. Lunch is on your own from 12:00 noon to 1:00 p.m.

Program Outline

Day 1

Introduction
Wire and Cable Applications

•    Wire and cable - specifications and conditions of use 

•    Conductor sizes, ampacities, temperature ratings
•    Flame spread ratings
•    Parallel conductors 

•    Underground conductors 

•    Sheath currents and eddy currents 

•    High voltage conductors

Grounding and Bonding
•    Electrical system grounding
•    Electrical equipment bonding
•    Bonding other systems
•    Single point bonding 

•    Grounding and bonding methods
•    High voltage grounding, ground potential rise, step and touch potentials

Protection and Control
•    Overload and overcurrent protection
•    Ground fault protection
•    Series rated equipment
•    Fuse and circuit-breaker applications
•    Switching and disconnection

Fire Alarm Systems and Fire Pumps 

•    Wiring and overcurrent protection methods

Day 2

Motor Applications
•    Service duty
•    Overcurrent and overload protection
•    Conductor ratings, services, feeders and branch circuits
•    Grouped motor protection
•    Motor disconnection
•    Motor controls

High Voltage Substations and Lines 

•    Electrical system fault levels
•    Basic impulse levels
•    Overcurrent protection
•    Lightning arresters
•    Clearances - lines and substations 

•    Liquid-filled electrical equipment

Hazardous Location
•    Class I flammable and explosive gases and vapours 

•    Class II combustible and conductive dusts 

•    Class III ignitable fibres and flyings 

•    Area classifications, divisions and groups 

•    Electrical equipment specifications for hazardous locations
•    Wiring systems and sealing method
•    Intrinsically safe and non-incendive circuits
•    Purged electrical systems

Emergency Power Supply, Unit Equipment, Exit Signs and Life Safety Systems
•    Emergency power supply
•    Emergency lighting and exit signs

Questions & Answers

Instructor

Les Stoch is President of L. Stoch and Associates, offering electrical engineering services, professional development and training. His industry experience includes 21 years with Ontario Hydro as an Electrical Inspection Manager and Engineer. Mr. Stoch obtained his Electrical Engineering Degree from Sir George Williams University (Concordia) in Montreal. He is a member of the Professional Engineers of Ontario, the American Society for Quality, the Ontario Electrical League and the International Association of Electrical Inspectors. He served for eight years on the Provincial Advisory Committee, which develops Ontario's Electrical Safety Code.  Mr. Stoch also audits electrical utilities for compliance with Ontario’s electrical distribution regulation OR 22/04 and carries out forensic engineering work – investigating and reporting on electrical fires and accidents.